Frictions and Steels
Please view our Order Info page before contacting us for an order, Thank You!
 |
4T65E Input Friction Set | $12.95 | This is a set of 4 friction plates that are made by Borg Warner and are OE replacements. We use these frictions in all of our rebuilds. 97-02 are the early style and 03+ are a late style and must be used with correct matching sprags. |
 |
4T65E Input Steel Plate Set | $7.95 | This is a set of 4 steel plates that when used with the above 4 frictions will complete the Input friction and steel package. These are all the same for all model year 4T65E transmissions though there are a few thickness options we can supply to help adjust clearance. |
 |
4T65E Upgraded 5 Clutch Input Set | $24.95 | The factory Input clutch arrangement uses 4 friction plates and works very well but we opt to use this 5 plate setup in our higher powered rebuilds and it will give 25% more clutch surface area. |
| 4T65E Input Backing Plate | If your original Input clutch backing plate is warped or has lots of burn or leopard spots on it then it should be replaced. | ||
 |
4T65E 2nd Friction Set | $17.95 | This is a set of 6 2nd friction plates. These plates are made by Borg Warner and are OE replacements. We use these frictions in all of our rebuilds for this clutch pack whether stock or heavily modified and with a properly set up transmission they hold up extremely well. |
 |
4T65E 2nd Steel Plate Set | $14.95 | This is a set of 5 2nd steel plates and when used in combination with the above fricions will complete the friction and steel package in stock form. The 2nd clutch clearance is often very loose from the factory so we suggest adding one extra stock thickness steel plate OR by substituting two stock thickness plates with two of the .090" thick plates listed below to tighten up the clutch clearance for best performance. |
 |
4T65E Extra Thick .090" Steel Plate | $4.95 | This plates are thicker than the original plates and are used to tighten up the 2nd clutch pack clearance as mentioned above. Often you can add one extra standard thickness steel plate to tighten up the clearnace but some drums dont allow enough room for this so using two of these plates works very well to tighten up the clearance. |
 |
4T65E 2nd Backing Plate | If your original 2nd clutch backing plate is warped or has lots of burn or leopard spots on it then it should be replaced. | |
| 4T65E 2nd Apply Plate | If your original 2nd clutch apply plate is warped or has lots of burn or leopard spots on it then it should be replaced. | ||
 |
4T65E 3rd Friction Set | $29.95 | This is a set of 10 3rd friction plates. These plates are made by Borg Warner and are OE replacements. We use these frictions in all of our rebuilds for this clutch pack whether stock or heavily modified and with a properly set up transmission they hold up extremely well. There are Tan plates and High Energy plates available for this application, please contact us to help decide which plates will work best for your application |
| 4T65E 3rd Backing Plate | $14.95 | If your original 3rd clutch backing plate is warped or has lots of burn or leopard spots on it then it should be replaced. | |
 |
4T65E Zpack 3rd Friction Set | $59.95 | This 3rd clutch set is the popular Zpack made by Raybestos. It is an improved design over the factory clutch setup and is designed to improve durability and reduce coning. This clutch pack retains the stock 10 friction plate arrangement. |
 |
Zpack 3rd Contents | The picture to the left shows the contents of the Zpack 3rd clutch set. It includes to thin steel apply plates, 10 friction plates, and one custom backing plate. | |
 |
4T65E 4th Friction Set | $7.95 | This is a set of 2 4th friction plates. These plates are made by Borg Warner and are OE replacements. We use these frictions in all of our rebuilds. This plate is the later design which has more oiling grooves to help prevent drag and hot spots on the steel plates and greatly helps with this. |
 |
4T65E 4th Steel Plate Set | $7.95 | This is a set of 2 steel plates that when used with the above 2 frictions will complete the 4th friction and steel package. |
 |
4T65E, 4T65EV/GT Tapshift Friction Set | $17.95 | This 4th friction set includes 2 external and 2 internally splined single-sided friction plates. This setup is used in all Volvo 4T65EV/GT models and 04+ GM Tapshift model transmissions |
 |
4T65E 4th Apply Plate | $14.95 | If your original 4th clutch apply plate is warped or has lots of burn or leopard spots on it then it should be replaced. This plate is pretty common to need replaced. This plate is for the standard 4th clutch set only, a special stepped style plate is used with the single-side friction sets. |
 |
4T65E Forward Apply Band | $44.95 | This is the band that sits all the way at the bottom of the case when the trans is apart and applies in forward ranges. On occasion the band may break and cause no forward movement in Drive range. These bands are new Borg Warner High Energy style bands and work in all 97+ 4T65E model transmissions. |
 |
4T65E Manual Coast 2-1 Band | $14.95 | This band only applies when the shifter is in manual 2 or 1 range and is used to aid in engine braking. If you manually shift your transmission often this band will likely be burnt and in need of replacement. These bands are new Borg Warner or Raybestos High Energy style bands and work in all 97+ 4T65E model transmissions |
 |
4T65E Reverse Apply Band | $44.95 | This band applies for reverse operation and is the first band that sits just under the driven sprocket support. In appearance is identical to the Forward band but is slightly larger and the lugs are spread apart much farther. These bands are new Borg Warner High Energy style bands and work in all 97+ 4T65E model transmissions |
